RE: Mx Road
Can you explain that further? Do you mean that you want the report chainage/distance of a 3D string representing the parking edge?
View ArticleRE: Corridor not updating changes in alignment MX SS3
Thanks Mark,Yes it reflects the change if the alignment is amended, but I have a lot of alignments that are done by others, I just want to be able to update them all at a go without going through them...
View ArticleCorridor not updating changes in alignment MX SS3
Dear All,I have a alignment file attached to my corridor file, when I delete and recreate the alignment in the alignment file the corridor gets corrupted and losses the link to the alignment. Is there...
View ArticleMx Road
is it possible to get chainages alongthe tapered portions of parking edge string in mxroad?
View ArticleRE: Mx Road
i have designed the centreline,to design the parking string,i should be knowing the chainages where it tapers, so is it possible to use the centreline string and get chainages for parking string from...
View ArticleClik here to view.
Corridor Modeler Template
I have a question I hope I can explain in this post.I have a simple template that is 3.5" thick with an 11' lane NB and an 11' lane SB crowned in the middle at 2% slopes. I have a CL alignment down the...
View ArticleRE: Draw long-section of M-string with a loop in it
Hello Simon,I am facing a similar problem of profile generation for a looped master string. Can you please advise if there is a workaround for this. I have raised a service request for this as well [...
View ArticleDraw long-section of M-string with a loop in it
My master string loops back on itself and when I draw it in long-section it shows as just a squiggly (technical term) line bunched up at the left side of the drawing. Strangely enough, section strings...
View ArticleClik here to view.
RE: "item browser" in PowerCivil ss3 (08.11.09.497)
Go to C:\Program Files (x86)\Bentley\PowerCivil V8i (SELECTSeries 3)\PowerCivil\CivilPlatform and edit the Bentley Civil Commands.cfg. Comment out the lines partaining to the configuration of the Item...
View Article"item browser" in PowerCivil ss3 (08.11.09.497)
Hi. I've got an IFC-file imported in PowerCivil ss3 (08.11.09.497) but the item browser gives me nothing ("No content available to display). If I open the same file in PowerCivil ss2 (08.11.07.615) I...
View ArticleGeopak, maximum number of points I can use to create a chain
Hello,I am in dire need of help and nowhere I seem to look can I get a complete answer other than, "there is no limit on the number of points you can store in Geopak." I have used Auto Store Graphics...
View ArticleClik here to view.
RE: PRINCIPIANTE EN FORO Y PRIMERA PREGUNTA
HugoDisculpa que nos tardamos en responderte...1. me puedes explicar como estas creando las hojas (ej. con las herramientas de microstation o con el generador de hojas de inroads)?si puedes, porfavor...
View ArticleRE: TDS codes - PC & PT Does not work as feature code anymore in SS3
I told it to expect the ST after the alpha code. I also am currently only working in Ss2, which is a little less advanced than what is in Ss3. Since you guys, MD SHA were still in earlier versions, I...
View ArticleQuestion regarding Vertical Alignments in Corridors
I have created a new vertical alignment for an access ramp using the Vertical Gore Tool. My mainline alignment and ramp alignment run in opposite directions. When I try to use the new alignments...
View ArticleRE: Question regarding Vertical Alignments in Corridors
Hi, can you please tell me what product and which product version you are using? I will need the 9-digit version number that can be found in Help > About.
View ArticleClik here to view.
RE: PowerInRoads Ss2 - Missing Civil Formatting
I think you are missing my question.First - it has been a while since I played with Data Acquisition and Civil Geometry. Still married to traditional InRoads per client situation. A recent post...
View ArticlePreference .xin file for InRoads SS2!
Can I apply "read only" to my preference .xin file so that I only have access to "read write" rather then having the rest of the group have read write access. Since im the owner of the .xin file I want...
View ArticleRE: Preference .xin file for InRoads SS2!
You can place it in a folder where everyone but you has read only access. Or if others have it open in read write access, you can ask them to switch it to read only -right click menu in the InRoads...
View ArticleRE: Drawing out profile and insert on sheet
Which software/version are you using? Bentley has 3 Civil products and the answer will vary depending upon the software and version.
View Article