Editing manhole and pipe
Hi1) Why does my native InRoads make a copy of manhole and pipe when moved in plan or profile?2) How can I change default level of my drainage whe creating in plan and profile...( it comes always in...
View ArticleRE: LiDAR Data & GEOPAK
Hello Marballe, Your understanding is correct.1) Trying to edit a TIN file that large would be very slow and likely to crash (run out of available memory blocks large enough to load/store the data)2)...
View ArticleRE: base plan
Hi Swarna, Your question is quite vague.You might need to provide a little more information before an answer can be suggested. Michael GilhamGlobal Solution Lead - CivilHATCHDirect: 61 7 3166...
View ArticleRE: Drainage
Hi Sigfús Which Civil application are you using? Michael GilhamGlobal Solution Lead - CivilHATCHDirect: 61 7 3166 6142www.hatch.com.au From: karon [mailto:bounce-karon@communities.bentley.com] Sent:...
View ArticleRE: GEOPAK-LABEL UPDATER
Load Plan View Labeler and look under the Tools drop down menu.
View ArticleRE: LiDAR Data & GEOPAK
Hello Marballe,Your understanding is correct.1) Trying to edit a TIN file that large would be very slow and likely to crash (run out of available memory blocks large enough to load/store the data)2)...
View ArticleRE: GEOPAK-GEOTECHNICAL TOOLS
like I said in post this post communities.bentley.com/.../97017.aspxGeopak does not produce geotech reports, it uses them to show boreholes in plan, profile and xs views in microstation
View ArticleRE: GEOPAK-ALIGNMENT LABELING
no, once you edit the geometry, you need to delete the labels and use D&C manager again to replot
View ArticleRE: GEOPAK-SECTIONS LABELING TOOLS
you are correct in the sense that they use microstation elements that are not necessarily associated with anything. but, the xs labeler only works on the specific section that the xs navigator is...
View ArticleGEOPAK-SECTIONS LABELING TOOLS
Hello,I am learning Geopak V8i SS2 using the Create Horizontal Alignments Learning Path and the help file as it applies.I have selected Application->Geopak->Roads->Cross Sections->Cross...
View ArticleRE: GEOPAK-PROFILE ELEVATION AND DP STATION OFFSET TOOLS
that tool works with the xs navigator. that means, at the current xs, you can select a datapoint (within the limits of the xs cell) and the labeler will give you the elevation of the profile (used to...
View ArticleGEOPAK-PROFILE ELEVATION AND DP STATION OFFSET TOOLS
Hello,I am learning Geopak V8i SS2 using the Create Horizontal Alignments Learning Path and the help file as it applies.I have selected Application->Geopak->Roads->Cross Sections->Cross...
View ArticleRE: GEOPAK-EDIT ELEMENT
unless you changed the name of the curve, it should automatically visualize the correct or modified geometry. you don't need to visualize the chain. you can visualize the chain, edit the curve and you...
View ArticleGEOPAK-EDIT ELEMENT
Hello,I am learning Geopak V8i SS2 using the Create Horizontal Alignments Learning Path and the help file as it applies.I am learning the Edit Element tools inside the Navigator. I unvisualized a...
View ArticleInRoads cannot be started if our Add-on is configured to load on launching.
Hi there,We have trouble to start InRoads if we configured our own C# Add-on to start when launching MicroStation. The InRoads application just quit without any error.MicroStation can be started...
View ArticleRE: Design Standards - Civil Message Center window/dialog not showing
Thanks, that did the trick
View ArticleRE: cross section labeler Error: "Job number can not be found in the active...
With some experimenting I seem to have come up with an answer. the source of the error is if the GPK was moved or renamed. Starting with a clean GPK and importing the chains it seems to be working. If...
View Articlecross section labeler Error: "Job number can not be found in the active...
MicroStation SS3 08.11.09.459GeoPak SS2 08.11.07.615ProjectWise SS4 08.11.11.111Windows 7 EnterpriseTrying to use the corridor modeler cross section labeling tool and every time I click on itI get an...
View Article