RE: POWER GEOPAK-ASCII POINT IMPORT
I appreciate your feedback, you have been very helpful. I do not find too much Learning content that is consistent with my needs but will comb thru what is available. There is a road course that...
View ArticlePOWER GEOPAK-ASCII POINT IMPORT
Hello,I am learning Power Geopak V8i SS2.I am trying to import ASCII points by selecting Geopak->Road->Geometry->Coordinate Geometry->File->Import->ASCII Points. The point file I am...
View ArticleRE: Thematic Display not calculating slopes correctly
After further investigation I do not believe this is a defect, If you turn off the thematic display option (which is set to slope) in the display style that is used, it will turn off the MS slope value...
View ArticleClik here to view.
Thematic Display not calculating slopes correctly
When I give a terrain model thematic display (slopes), it doesn't appear to be calculating the slopes correctly (see screenshots below). Can someone let me know what I'm doing wrong?Thanks,Matt
View ArticleRE: OpenRoads - Updadte Cross Sections
Hi Marc,A change request was previously submitted (S-99108) for the ability to update cross sections. If you’d like, I can also submit a change request for the ability to updated cross sections when a...
View ArticleOpenRoads - Updadte Cross Sections
If I have created a set of cross sections in a cross section model in OpenRoads SS3 how can these sections be updated if the corridor changes?Marc
View ArticleRE: Cut-Slope Rounding in OpenRoads
Thanks for the reply, I like your suggested change. Have you formally submitted this request to Bentley? Have you had any response?
View ArticleRE: Modeler Combines independent End Conditions
Kevin both the component name override and the point properties feature name override have different names.
View ArticleRE: Moving structure
Hi Sigfus,Ensure that you have Tools>Lock>Pencil Mode selected, also make sure that Tools>Lock>Delete Ink is selected. This should prevent your duplicate structures.Thanks!
View ArticleMoving structure
HiWhy is that everytime when i move structure in profile and plan there is created a copy of both the structure and the pipe. Which I have to delete afterwardVers. PowerCivil for Denmark...
View ArticleRE: IR Ss2 - MS Ss3 - File got too big?
Very Sad Microstation is still on 32bit, don't know how many months to wait for 64bit.
View ArticleIR Ss2 - MS Ss3 - File got too big?
I was importing some Lidar LAS files via Data Acquisition, and suddenly I crashed, and now when I go to open the file, it says: "Unable to open design file. Contact your site administrator or technical...
View ArticleRE: Modeler Combines independent End Conditions
Can you post an IRD and ALG that show this problem (might need the DTM as well... if the end conditions are targeting it).You can post the files to this thread, or post them on our FTP following the...
View ArticleRE: Modeler Combines independent End Conditions
Hi Kevin, I uploaded the files to the FTP site.
View ArticleClik here to view.
Modeler Combines independent End Conditions
I have a sidewalk template with an end condition and I have a road template with an end condition. In modeler they display fine as shown in the image below.When I run the modeler to create the surface,...
View ArticleRE: Trying to get my end condition to seek a horizontal and vertical alignment
One rule I have that might be causing this problem is never to use a point control on the last point of an end condition. If you have a horizontal AND vertical you want an end condition to follow,...
View ArticleRE: Trying to get my end condition to seek a horizontal and vertical alignment
Kevin are you talking about setting the constraints to horizontal and vertical in the point properties dialog box?
View ArticleRE: Trying to get my end condition to seek a horizontal and vertical alignment
No, I'm talking about Point Controls, not point constraints. In your original post you used the term "Point Controls" so I wanted to make sure you did not assign a Point Control to an end condition...
View ArticleRE: Trying to get my end condition to seek a horizontal and vertical alignment
I was talking about point controls and I did assign them to seek the H/V alignment. After reading your post I deleted the point controls in modeler per your comments and I found the targeting option on...
View Article