Call OpenRoads function (InRoads SELECTseries 3) under started MicroStation
Any idea to call OpenRoads functions under started MicroStation?Load_InRoads_SS3 = 1 variable is added into CFG file. InRoads Ss3 Explorer can be started under started MicroStationHowever, the...
View ArticleAttaching corridors to multiple geometry
Is it possible to add corridors to multiple geometry lines. Now I add them one by one and this can be very time consuming.Further do I have the same question for exporting surfaces to for example...
View ArticleClik here to view.
How to Apply Linear Template in Open Roads?
Hello!In InRoads SS2 is a command called Apply Template ... that I use often.In SS3, it is replaced with a similar command Apply Linear Template. In SS3, you can not choose the interval of Template...
View ArticleMinimum Distance between 2 alignments
Any function in InRoads can locate station (chainage or coordinates) with the minimum distance between 2 alignments (horizontal and vertical).
View ArticleRe: Cross Section Labeling Error
can you open the labeler in other computers? with the same project and gpk?
View ArticleClik here to view.
Re: Minimum Distance between 2 alignments
There is not a command in InRoads that will report or output this information however you can use a tool in MicroStation in conjunction with InRoads to get this information you want. In MicroStation,...
View ArticleRe: How to Apply Linear Template in Open Roads?
Hi,Check your configuration variable: CIVIL_DEFAULT_LINEAR_STROKINGKindly,Adam
View ArticleRe: Call OpenRoads function (InRoads SELECTseries 3) under started MicroStation
With the addition of the OpenRoads tools, the integration with Microstation and InRoads is necessary. Therefore in order to get the OpenRoads tools in MicroStation you MUST start up InRoads. This is...
View ArticleRe: How to Apply Linear Template in Open Roads?
If a value is not set for the template drop, the command defaults to 10 which may have caused the behavior seen.
View ArticleEdits to Special Ditch Profiles Not Being Recognized
(Posted on behalf of Be Communities Member)I have created special ditch profiles for the end conditions to target in my templates and it worked the first time but now it is not recognizing changes to...
View ArticleClik here to view.
Re: Edits to Special Ditch Profiles Not Being Recognized
How are you targeting the vertical alignment? Are you using priorities in the template or an end condition exception? I assume that you are setting your End Condition Properties to Target Type...
View ArticleRe: Attaching corridors to multiple geometry
Are you using InRoads or GEOPAK? Also, are you using version SS2 or SS3?
View ArticleRe: Cross Section Labeling Error
Yes, Nico. I am able to use it on other computers.I think there is a possibility that my installations of MicroStation, Geopak (SS2 and SS3), and InRoads were not done correctly. To verify the...
View ArticleMultiple Installs (MS, GPK, InRoads)
For a variety of reasons, I am trying to get MicroStation, Geopak (both SS2 and SS3), and InRoads (SS2) installed on my machine. I had it all installed at one point, but I had a variety of issues that...
View ArticleRe: Multiple Installs (MS, GPK, InRoads)
Can I run GEOPAK SS2 and GEOPAK SS3 on the same machine?Yes, with the following recommendations:a. Access the softwares using their respective icons. (with either the “-wsLoad_GEOPAK_SS2” or...
View ArticleRe: Multiple Installs (MS, GPK, InRoads)
Thanks for the quick reply Nico. Is there anything that I need to do when uninstalling to make sure everything is gone? I want to do whatever I can to avoid any hiccups.Thanks.
View ArticleGenerate a Quick Profile for a Reference Check
(Posted on behalf of Be Communities Member) We have had the ability in the past using Terramodel to draw a quick profile of the active surfaces in the file. This is simply a one click button command...
View ArticleClik here to view.
Re: Generate a Quick Profile for a Reference Check
With the new OpenRoads tools, we have the ability to create a Profile Model from an element in the design file. When you create this profile model, it will take the active terrain model in the Civil...
View ArticleClik here to view.
SS3 Profile Associations / Dependencies
Using OpenRoads, it's easy to find out which element a given element is dependent on horizontally - and to change that reference association to a different element if necessary. How do you do the same...
View ArticleInRoads SS3 - correct location for Graphical Filter DGNLIB?
Hi All,I created a DGNLIB that contains terrain Graphical Filters. Unfortunately, I've been unable to have that DGNLIB show up in my Project Explorer>Civil Standards>Libraries>Filters...
View Article